SS Attic GE 4TTV8X-TUD2ACV 4.0T
SS Attic GE 4TTV8X-TUD2ACV 4.0T
$275.09**
per month- Manufacturer Rebate: $500.00
Standard heating and cooling systems are constantly starting and stopping, which tend to cause temperature fluctuations between cycles. The XV18 TruComfort variable speed system is designed to maintain consistent temperatures in your home by running at lower speeds for longer periods of time-without all the harsh stops and starts.
APPLY FOR FINANCING
Trane XV18 Air Conditioner
• Woven Spine Fin™ coil
• Variable-speed fan motor
• Swept fan blade
• Compressor sound insulator
• Climatuff® Variable Speed inverter compressor
• ComfortLink™ II capability
Trane XC80 Gas Furnace
• ComfortLink™ II
• Continuous Comfort-R™ mode
• Two-stage heat
• Three-wire connections
• Two-speed draft inducer
• Silicon nitride igniter
• Variable-speed communicating ECM blower motor
• Digital user interface for easy set-up and diagnostics
• Certified to 2% air leakage
Trane 4TXC Cased Evaporator Coil
• Enhanced fin design for efficiency and humidity control
• Double-sloped high temp drain pan
• All-Aluminum to prevent formicary corrosion
Trane XL850 ComfortLink™ II Connected Control
• Remote Climate Access included
• Built in Bridge for Z-Wave devices
• ComfortLink™ II commuications
• WiFi or Ethernet Connectivity
• Trane Diagnostics ready
• Compatible with 24 volts systems (requires relay panel – sold separatly)
• 5 heat / 2 cool
• 7-day programmable with up to 4 periods/day
• 4.3” color display
• Dual Fuel Capable
• 2 filter change reminders
• 5-day weather forecast, local radar & alerts
• Allergy and quick clean cycles
• Ventilation control
• Maintenance reminders
• Customizable home screen
• Embedded diagnostics
• Color: Designer Silver
AHRI # 208443258
SEER/EER 18.00/12.80
Cooling Capacity 48,000
Cooling Stages 700
Heating Capacity 80,000
Heating Stages 2
Trane Condenser Model # 4TTV8X48A1000*
Trane Furnace Model # TUD2C080ACV42*
Trane Evaporator Model # 4TXCC009DS3HC*
Trane Control Model # TCONT850AC52UB
Air Conditioner
- Furnish and install a new electrical disconnect box with new fuses, wire, and conduit.
- Re-insulate the refrigerant lines outside and in the attic.
- Install conduit around the low-voltage wiring outside to stop sun-rot and rodent damage.
Gas Furnace and Evaporator Coil
- Furnish and install a new hanging system in the attic using high strength Unistrut, cable, and new hardware.
- Furnish and install a new secondary overflow pan with coil support rails.
- Furnish and install a new condensate p-trap with vent and clean-out stub.
- Furnish and install a condensate overflow shut-off switch.
- Purge and water test condensate drain lines for proof of proper drainage.
- Furnish and install a new sheet-metal return air plenum with a 1” fiberglass insulation liner for superior thermal resistance.
- Furnish and install a new properly sized sheet-metal supply air plenum for optimal airflow distribution.
- Furnish and install balancing dampers to provide greater control of airflow into the supply ducts.
- Duct seal connections to plenums with low-VOC mastic.
- Seal evaporator cabinet penetrations to prevent known air leakage locations with sealing compound.
- Furnish and install a natural gas sediment trap with flexible appliance connector and new shut-off valve.
- Furnish and install a new flue pipe to the existing roof penetration for furnace carbon monoxide exhaust.
- Furnish and install a new 115v appliance cord.
Thermostat
- Configure the control to match the specifications of the equipment installed.
- Setup control for Trane remote diagnostics.
- Setup control with customer defined temperature setpoints and schedules.
- Seal wall penetration behind thermostat with sealing compound.
Other
- On-site inspection to evaluate the particular scope of work.
- Heat load calculation using Manual J software to determine capacity requirements for proper equipment sizing.
- Property protection measures using floor covers and plastic sheeting.
- Existing equipment tear-down, removal, and off-site disposal.
- Exterior work areas broom swept, and interior work areas vacuumed.
- Flow nitrogen through refrigerant lines while brazing to prevent carbon build-up and system contamination.
- Evacuate refrigerant lines to achieve a supporting vacuum at 500 microns or better.
- Equipment start-up and calibration to assure safe, proper, and efficient operation.
- Warranty registration with manufacturer to secure extended warranty terms as needed.
- Process utility rebate application if applicable.
- Quality assurance inspection to check operational performance, safety, and overall installation quality.
- Enrollment into the Cool Club Standard membership to cover the first year of maintenance check-ups.
Every Trane residential unit comes with a Limited Warranty. It covers parts that break because of manufacturer defect, but does not cover the cost of labor.
• 12-year base limited warranty on compressor through Trane
• 10-year base limited warranty on internal functional parts through Trane
• Lifetime base limited warranty on heat exchanger through Trane
Recommended Upgrades
• No labor charges for 10-years
• No refrigerant charges
• No deductibles
• No diagnostic charges (one per year)
• Covers all equipment
• Free to transfer
• Independent 3rd party coverage
• Policy underwritten and insured by DAC
• MERV 11 Media Filter
• 5″ Depth 18 Gauge Metal Painted Cabinet w/ Fully insulated R-4.2 Door
• Air Tite Door Construction with Gasketing and Quarter Turn Easy Open Latch
• Up to 100 times more effective than a standard 1” throwaway filter
• Power door provides easy access to internal components and features a filter status display as well as safety interlocks that automatically shut down the power when the door is opened for maintenance or cleaning
• Removes up to 99.98% @.3 Micron size allergens from the filtered air”
• Allergy and Asthma Friendly® Certified
• Quiet operation
• Helps keep heat outside during summer
• Helps keep heat inside during winter
• Reduces utility costs
• Extends temperature drift time inside
• Reduced cooling load helps HVAC equipment
• Higher R-Value improves resistance to heat flow
• Proper sizing and design provides better air dynamics and air delivery
• 30-year life expectancy
• Even airflow means no more hot and cold spots
• Reduces Odors
• Helps prevent the spread of bacteria and viruses
• Combats toxins and pollutants
• Installs in the duct system to provide improved air quality throughout the entire home
*The Wells Fargo Home Projects credit card is issued by Wells Fargo Bank, N.A., an Equal Housing Lender. Special terms apply to qualifying purchases with approved credit. The special terms APR will continue to apply until all qualifying purchases are paid in full. The monthly payment for this purchase will be the amount that will pay for the purchase in full in equal payments during the promotional (special terms) period. The APR for Purchases will apply to certain fees such as a late payment fee or if you use the card for other transactions. For new accounts, the APR for Purchases is 28.99%. If you are charged interest in any billing cycle, the minimum interest charge will be $1.00. This information is accurate as of 10/20/2021 and is subject to change. For current information, call us at 1-800-431-5921. Offer expires 12/31/22.
**Monthly payment is based on purchase price alone. Credit purchases subject to credit approval. Other transactions may affect the monthly payment.
***Reflects all current manufacturer rebates, utility rebates, and other offers if available.